manpages.info - online man pages   

SunOS man pages : xntpdc (1)

Maintenance Commands                                   xntpdc(1M)

NAME

xntpdc - special NTP query program

SYNOPSIS

xntpdc [ -ilnps ] [ -c command ] [ host ] [ ... ]

DESCRIPTION

xntpdc queries the xntpd daemon about its current state and requests changes in that state. You can run xntpdc in interactive mode or in controlled using command line argu- ments. Extensive state and statistics information is available through the xntpdc interface. In addition, nearly all the configuration options which can be specified at start up using xntpd's configuration file may also be specified at run time using xntpdc. If one or more request options is included on the command line when xntpdc is executed, each of the requests is sent to the NTP servers running on each of the hosts given as command line arguments, or on the local host by default. If no request options are given, xntpdc attempts to read com- mands from the standard input and execute these on the NTP server running on the first host specified on the command line, again defaulting to the local host when no other host is specified. xntpdc prompts for commands if the standard input is a terminal device. xntpdc uses NTP mode 7 packets to communicate with the NTP server, and can be used to query any compatable server on the network which permits it. As NTP is a UDP protocol, this communication is somewhat unreliable, especially over large distances. xntpdc does not attempt to re-transmit requests, and times requests out if the remote host is not heard from within a suitable timeout time. The operation of xntpdc is specific to the particular imple- mentation of the xntpd daemon. You can expect xntpdc to work only with this and maybe some previous versions of the dae- mon. Requests from a remote xntpdc program that affect the state of the local server must be authenticated. This requires that both the remote program and local server share a common key and key identifier.

OPTIONS

xntpdc reads interactive format commands from the standard input. If you specify the -c, -l, -p or -s option, the specified queries are sent to the hosts immediately. The following command line options are supported: SunOS 5.8 Last change: 29 Sep 1999 1 Maintenance Commands xntpdc(1M) -c command... Add command to the list of commands to execute on the specified hosts. command is interpreted as an interac- tive format command. Multiple -c options may be specified. -i Force xntpdc to operate in interactive mode. Prompts are written to the standard output. Commands are read from the standard input. -l Obtain a list of peers which are known to the servers. This option is equivalent to -c listpeers. See listpeers in Control Message Commands. -n Output all host addresses in dotted-quad numeric for- mat rather than converting to the canonical host names. -p Print a list of the peers known to the server as well as a summary of their state. This option is equivalent to -c peers. See peers in Control Message Commands. -s Print a list of the peers known to the server as well as a summary of their state, but in a slightly dif- ferent format than the -p option. This option is equivalent to -c dmpeers. See dmpeers in Control Mes- sage Commands.

OPERANDS

The following operands are supported:

USAGE

Interactive Commands The interactive commands consist of a keyword (command_keyword) followed by zero to four arguments. You need to entry only enough characters of the command_keyword to uniquely identify it. The output of an interactive com- mand is sent to the standard output by default. You can send the output of an interactive command to a file by appending a <, followed by a file name, to the command line. A number of interactive format commands are executed entirely within the xntpdc program itself and do not result in NTP mode. SunOS 5.8 Last change: 29 Sep 1999 2 Maintenance Commands xntpdc(1M) The following interactive commands are supported: ? [ command_keyword ] Without an argument, print a list of ntpq command key- words. If command_keyword is specified, print function and usage information about the command_keyword. delay milliseconds Specify a time interval to add to timestamps included in requests which require authentication. This enables (unreliable) server reconfiguration over long delay network paths or between machines whose clocks are unsynchronized. Because the server no longer requires timestamps in authenticated requests, this command may be obsolete. help [ command_keyword ] Without an argument, print a list of ntpq command key- words. If command_keyword is specified, print function and usage information about the command_keyword. host hostname Set the host (hostname) to which future queries are sent. Specify hostname as a host name or a numeric address. hostnames [ yes | no ] Print hostnames or numeric addresses in information displays. Specify yes to print host names. Specify no to print numeric addresses. The default is yes, unless the -n command line option is specified. keyid keyid Enable specification of a key number (keyid) to authenticate configuration requests. keyid must correspond to a key number the server has been config- ured to use for this purpose. passwd Prompt user to enter a password to authenticate confi- guration requests. The password is not displayed , and must correspond to the key configured for use by the NTP server for this purpose. If the password does not correspond to the key configured for use by the NTP server, requests are SunOS 5.8 Last change: 29 Sep 1999 3 Maintenance Commands xntpdc(1M) not successful. quit Exit xntpdc. timeout millseconds Specify a timeout period for responses to server queries. The default is approximately 8000 milliseconds. As xntpdc retries each query once after a timeout, the total waiting time for a timeout is twice the timeout value set. Control Message Commands Query commands result in NTP mode 7 packets containing requests for information being sent to the server. These control message commands are read-only commands in that they make no modification of the server configuration state. The following control message commands are supported: clkbug Obtain debugging information for a reference clock driver. This information is provided only by some clock drivers. clockinfo clock_peer_address [...] Obtain and print information concerning a peer clock. The values obtained provide information on the setting of fudge factors and other clock performance informa- tion. dmpeers Obtain a list of peers for which the sserver is main- taining state, along with a summary of that state. The peer summary list is identical to the output of the peers command, except for the character in the leftmost column. Characters only appear beside peers which were included in the final stage of the clock selection algorithm. A . indicates that this peer was cast off in the falseticker detection, while a + indi- cates that the peer made it through. A * denotes the peer with which the server is currently synchronizing. iostats Print statistics counters maintained in the input- output module. kerninfo Obtain and print kernel phase-lock loop operating SunOS 5.8 Last change: 29 Sep 1999 4 Maintenance Commands xntpdc(1M) parameters. This information is available only if the kernel has been specially modified for a precision timekeeping function. listpeers Obtain and print a brief list of the peers for which the server is maintaining state. These should include all configured peer associations as well as those peers whose stratum is such that they are considered by the server to be possible future synchonization candidates. candidates. loopinfo [ oneline | multiline ] Print the values of selected loop filter variables. The loop filter is the part of NTP which deals with adjusting the local system clock. The oneline and multiline options specify the format in which this information is printed. multiline is the default. The offset is the last offset given to the loop filter by the packet processing code. The frequency is the frequency error of the local clock in parts-per- million (ppm). The time_const controls the stiffness of the phase-lock loop and thus the speed at which it can adapt to oscillator drift. The watchdog timer value is the number of seconds which have elapsed since the last sample offset was given to the loop filter. memstats Print statistics counters related to memory allocation code. monlist [version] Obtain and print traffic counts collected and main- tained by the monitor facility. The version number should not normally need to be specified. peers Obtain a list of peers for which the server is main- taining state, along with a summary of that state. The following summary information is included: o Address of the remote peer. o Local interface address. If a local address SunOS 5.8 Last change: 29 Sep 1999 5 Maintenance Commands xntpdc(1M) has yet to be determined it is 0.0.0.0. o Stratum of the remote peer. A stratum of 16 indicates the remote peer is unsynchron- ized. o Polling interval, in seconds. o Reachability register, in octal. o Current estimated delay, offset and disper- sion of the peer, in seconds. o Mode in which the peer entry is operating. This is represented by the character in the left margin. A + denotes symmetric active, a - indicates symmetric passive, a = means the remote server is being polled in client mode, a ^ indicates that the server is broadcasting to this address, a ~ denotes that the remote peer is sending broadcasts and a * marks the peer the server is currently synchonizing to. o Host. This field may contain a host name, an IP address, a reference clock implementation name with its parameter or REFCLK (imple- mentation number, parameter). On hostnames no only IP-addresses is displayed. pstats peer_address [...] Show the per-peer statistic counters associated with the specified peers. reslist Obtain and print the server's restriction list. Generally, this list is printed in sorted order. showpeer peer_address [...] Show a detailed display of the current peer variables for one or more peers. Most of these values are described in the NTP Version 2 specification. sysinfo Print a variety of system state variables that are related to the local server. The output from sysinfo is described in NTP Version 3 SunOS 5.8 Last change: 29 Sep 1999 6 Maintenance Commands xntpdc(1M) specification, RFC-1305. All except the last four lines are described in the NTP Version 3 specifica- tion, RFC-1305. The system flags show various system flags, some of which can be set and cleared by the enable and disable configuration commands, respectively. These are the auth, bclient, monitor, pll, pps and stats flags. See the xntpd documentation for the meaning of these flags. There are two additional flags which are read only, the kernel_pll and kernel_pps. These flags indi- cate the synchronization status when the precision time kernel modifications are in use. The kernel_pll indicates that the local clock is being disciplined by the kernel, while the kernel_pps indicates the kernel discipline is provided by the PPS signal. The stabil- ity is the residual frequency error remaining after the system frequency correction is applied and is intended for maintenance and debugging. In most archi- tectures, this value initially decreases from as high as 500 ppm to a nominal value in the range .01 to 0.1 ppm. If it remains high for some time after starting the daemon, something may be wrong with the local clock, or the value of the kernel variable tick may be incorrect. The broadcastdelay shows the default broad- cast delay, as set by the broadcastdelay configuration command. The authdelay shows the default authentica- tion delay, as set by the authdelay configuration com- mand. sysstats Print statistics counters maintained in the protocol module. timerstats Print statistics counters maintained in the timer/event queue support code. Runtime Configuration Requests The server authenticates all requests that cause state changes in the server. The server uses a configured NTP key to accomplish this. This facility can also be disabled by the server by not configuring a key). You must make the key number and the corresponding key known to xtnpdc. Use the keyid or passwd commands to do so. The passwd command prompts users for a password to use as the encryption key. It also prompts automatically for both the key number and password the first time a command which would result in an authenticated request to the server is given. Authentication provides verification that the SunOS 5.8 Last change: 29 Sep 1999 7 Maintenance Commands xntpdc(1M) requester has permission to make such changes. It also gives an extra degree of protection against transmission errors. Authenticated requests always include a time stamp in the packet data. The time stamp is included in the computation of the authentication code. This timestamp is compared by the server to its receive time stamp. If the time stamps differ by more than a small amount the request is rejected. Time stamps are rejected for two reasons. First, it makes simple replay attacks on the server, by someone who might be able to overhear traffic on your LAN, much more difficult. Second, it makes it more difficult to request configuration changes to your server from topologically remote hosts. While the reconfiguration facility works well with a server on the local host, and may work adequately between time- synchronized hosts on the same LAN, it works very poorly for more distant hosts. If reasonable passwords are chosen, care is taken in the distribution and protection of keys and appropriate source address restrictions are applied, the run time reconfiguration facility should provide an adequate level of security. The following commands make authenticated requests. addpeer peer_address [ keyid ] [ version ] [ prefer ] Add a configured peer association at the given address and operating in symmetric active mode. An existing association with the same peer may be deleted when this command is executed, or may simply be converted to conform to the new configuration, as appropriate. If the optional keyid is a non-zero integer, all out- going packets to the remote server will have an authentication field attached encrypted with this key. If the keyid is 0 or omitted, no authentication is done. Specify version as 1, 2 or 3. The default is 3. The prefer keyword indicates a preferred peer. This keyword is used primarily for clock synchronisation if possible. The preferred peer also determines the vali- dity of the PPS signal - if the preferred peer is suitable for synchronisation so is the PPS signal. addserver peer_address [ keyid ] [ version ] [ prefer ] Identical to the addpeer command, except that the operating mode is client. addtrap [ address [ port ] [ interface ] SunOS 5.8 Last change: 29 Sep 1999 8 Maintenance Commands xntpdc(1M) Set a trap for asynchronous messages. authinfo Return information concerning the authentication module, including known keys and counts of encryptions and decryptions which have been done. broadcast peer_address [ keyid ] [ version ] [ prefer ] Identical to the addpeer command, except that the operating mode is broadcast. In this case a valid key identifier and key are required. The peer_address parameter can be the broadcast address of the local network or a multicast group address assigned to NTP. If a multicast address, a multicast-capable kernel is required. clrtrap [ address [ port ] [ interface] Clear a trap for asynchronous messages. delrestrict address mask [ ntpport ] Delete the matching entry from the restrict list. fudge peer_address [ time1 ] [ time2 ] [ stratum ] [ refid ] Provide a way to set certain data for a reference clock. readkeys Cause the current set of authentication keys to be purged and a new set to be obtained by re-reading the keys file. The keys file must have been specified in the xntpd configuration file. This enables encryption keys to be changed without restarting the server. restrict address mask flag [ flag ] This command operates in the same way as the restrict configuration file commands of xntpd. reset Clear the statistics counters in various modules of the server. traps Display the traps set in the server. trustkey keyid [...] untrustkey keyid [...] These commands operate in the same way as the trusted- key and untrustkey configuration file commands of xntpd. unconfig peer_address [...] Cause the configured bit to be removed from the speci- fied peers. In many cases this causes the peer SunOS 5.8 Last change: 29 Sep 1999 9 Maintenance Commands xntpdc(1M) association to be deleted. When appropriate, however, the association may persist in an unconfigured mode if the remote peer is willing to continue on in this fashion. unrestrict address mask flag [ flag ] Unrestrict the matching entry from the restrict list.

ATTRIBUTES

See attributes(5) for descriptions of the following attri- butes: ____________________________________________________________ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | |_____________________________|_____________________________| | Availability | SUNWntpu | |_____________________________|_____________________________|

SEE ALSO

ntpdate(1M), ntpq(1M), ntptrace(1M), xntpd(1M), rename(2), attributes(5) SunOS 5.8 Last change: 29 Sep 1999 10