manpages.info - online man pages   

SunOS man pages : routed (1)

Maintenance Commands                                in.routed(1M)

NAME

in.routed, routed - network routing daemon

SYNOPSIS

/usr/sbin/in.routed [ -s ] [ -q ] [ -t ] [ -g ] [ -S ] [ -v ] [ logfile ]

DESCRIPTION

in.routed is invoked at boot time to manage the network routing tables. The routing daemon uses a variant of the Xerox NS Routing Information Protocol in maintaining up-to- date kernel routing table entries. In normal operation, in.routed listens on udp(7P) socket 520 (decimal) for routing information packets. If the host is an internetwork router, it periodically supplies copies of its routing tables to any directly connected hosts and networks. When in.routed is started, it uses the SIOCGIFCONF ioctl(2) to find those directly connected interfaces configured into the system and marked "up" (the software loopback interface is ignored). If multiple interfaces are present, it is assumed the host will forward packets between networks. in.routed then transmits a request packet on each interface (using a broadcast packet if the interface supports it) and enters a loop, listening for request and response packets from other hosts. When a request packet is received, in.routed formulates a reply based on the information maintained in its internal tables. The response packet contains a list of known routes, each marked with a "hop count" metric (a count of 16, or greater, is considered "infinite"). The metric associated with each route returned, provides a metric relative to the sender. request packets received by in.routed are used to update the routing tables if one of the following conditions is satis- fied: o No routing table entry exists for the destination net- work or host, and the metric indicates the destination is "reachable" (that is, the hop count is not infin- ite). o The source host of the packet is the same as the router in the existing routing table entry. That is, updated information is being received from the very internetwork router through which packets for the des- tination are being routed. o The existing entry in the routing table has not been SunOS 5.8 Last change: 12 Nov 1998 1 Maintenance Commands in.routed(1M) updated for some time (defined to be 90 seconds) and the route is at least as cost effective as the current route. o The new route describes a shorter route to the desti- nation than the one currently stored in the routing tables; the metric of the new route is compared against the one stored in the table to decide this. When an update is applied, in.routed records the change in its internal tables and generates a response packet to all directly connected hosts and networks. in.routed waits a short period of time (no more than 30 seconds) before modi- fying the kernel's routing tables to allow possible unstable situations to settle. In addition to processing incoming packets, in.routed also periodically checks the routing table entries. If an entry has not been updated for 3 minutes, the entry's metric is set to infinity and marked for deletion. Deletions are delayed an additional 60 seconds to insure the invalidation is propagated throughout the internet. Hosts acting as internetwork routers gratuitously supply their routing tables every 30 seconds to all directly con- nected hosts and networks. In addition to the facilities described above, in.routed supports the notion of "distant" passive and active gate- ways. When in.routed is started up, it reads the file gate- ways to find gateways which may not be identified using the SIOCGIFCONFioctl. Gateways specified in this manner should be marked passive if they are not expected to exchange routing information, while gateways marked active should be willing to exchange routing information (that is, they should have a in.routed process running on the machine). Routes through passive gateways are installed in the kernel's routing tables once upon startup. They may change, depending upon routing information they receive from other gateways. Information regarding their existence is not included in any routing information transmitted. Active gateways are treated equally to network interfaces. Routing information is distributed to the gateway, and if no routing information is received for a period of time, the associated route is deleted. The gateways is comprised of a series of lines, each in the following format: < net | host > filename1 gateway filename2 metric value < passive | active > SunOS 5.8 Last change: 12 Nov 1998 2 Maintenance Commands in.routed(1M) The net or host keyword indicates if the route is to a net- work or specific host. filename1 is the name of the destination network or host. This may be a symbolic name located in networks or hosts, or an Internet address specified in "dot" notation; see inet(3SOCKET). filename2 is the name or address of the gateway to which messages should be forwarded. value is a metric indicating the hop count to the destina- tion host or network. The keyword passive or active indicates if the gateway should be treated as passive or active (as described above).

OPTIONS

-g Is used on internetwork routers to offer a route to the ``default'' destination. This is typically used on a gateway to the Internet, or on a gateway that uses another routing protocol whose routes are not reported to other local routers. -q Is the opposite of the -s option. -s Forces in.routed to supply routing information whether it is acting as an internetwork router or not. -S If in.routed is not acting as an internetwork router it will, instead of entering the whole routing table in the kernel, only enter a default route for each internetwork router. This reduces the the memory requirements without losing any routing reliability. -t All packets sent or received are printed on standard output. In addition, in.routed will not divorce itself from the controlling terminal so that interrupts from the keyboard will kill the process. Any other argument supplied is interpreted as the name of the file in which in.routed's actions should be logged. This log contains information about any changes to the routing tables and a history of recent messages sent and received which are related to the changed route. -v Allows a logfile (whose name must be supplied) to be created showing the changes made to the routing tables with a timestamp.

FILES

/etc/gateways for distant gateways SunOS 5.8 Last change: 12 Nov 1998 3 Maintenance Commands in.routed(1M) /etc/networks associations of Internet Protocol network numbers with network names /etc/hosts Internet host table

ATTRIBUTES

See attributes(5) for descriptions of the following attri- butes: ____________________________________________________________ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | |_____________________________|_____________________________| | Availability | SUNWcsu | |_____________________________|_____________________________|

SEE ALSO

route(1M), ioctl(2), inet(3SOCKET), attributes(5), inet(7P), udp(7P)

NOTES

The kernel's routing tables may not correspond to those of in.routed for short periods of time while processes that utilize existing routes exit; the only remedy for this is to place the routing process in the kernel. in.routed should listen to intelligent interfaces, such as an IMP, and to error protocols, such as ICMP, to gather more information. in.routed initially obtains a routing table by examining the interfaces configured on a machine and the gateways file. It then sends a request on all directly connected networks for more routing information. in.routed does not recognize or use any routing information already established on the machine prior to startup. With the exception of interface changes, in.routed does not see any routing table changes that have been done by other programs on the machine, for example, routes added, deleted or flushed by way of the route(1M) command. Therefore, these types of changes should not be done while in.routed is running. Rather, shut down in.routed, make the changes required, and then restart in.routed. SunOS 5.8 Last change: 12 Nov 1998 4